• Graphtec midi DATALOGGER GL980 Series

HIGH SPEED 1 MS/S SIMULTANEOUS SAMPLING WITH ISOLATED INPUT

Graphtec midi Loggger GL980 Features Hi Speed Simultaneous Sampling Isolated Input.jpg

GL980 is equipped with an isolated input mechanism to protect signals from interferences caused by noise from other channels. 16-bit A/D converter adopted to achieve hi-speed and hi-resolution measurements.

SIMULTANEOUS SAMPLING
GL980 utilizes simultaneous sampling to eliminate slowdown in sampling rate by using multiple A/D converters in simultaneous sampling method. Eight individual A/D converters in each channel sustains the maximum sampling speed for all eight channels to measure high speed rapid voltage fluctuation and multi-channel vibration measurement.
Sampling interval: 1 µs to 1 min (in steps of 1, 2, 5)

EXTERNAL SAMPLING FUNCTION
Sampling of the logger is performed in sync with an external device using an external signal input.
Maximum input frequency: 100 kHz

* B-513 Input/Output cable for GL is required.


CALCULATION FUNTION BETWEEN CHANNELS

our arithmetic operations (Addition, subtraction, multiplication and division) are available using two analog input channels.
* Data can be saved only in GBD file format.

 Example

CH2 = CH3 * CH1
(CH2 is a value obtained by multiplying the values of CH3 and CH1)
* Value of calculated results are displayed and saved into data file.

 

TRIGGER FUNCTION

The trigger in this unit has multiple functions including level trigger of input signal value for each channel.

 Trigger action

Start or stop capturing data by triggering

 Trigger source

Off, Measured signal level, Alarm, External, Scheduled time, Scheduled day, Elapsed time
* When trigger is used for starting action, level of measured signal can be set for each channel.

 Threshold

Analog input: High or Rising, Low or Falling, Window-in, Window-out
Logic input: H or L (4-channel signal pattern)
Pulse input: High or Rising, Low or Falling, Window-in, Window-out
Combination: Level OR, Level AND, Edge OR, Edge AND

 

ALARM FUNCTION & SIGNAL OUTPUT

Threshold of an alarm can be set for each channel. When an alarm is triggerred notification is sent by following methods.

Alarm threshold

Analog input: High, Low, Window-in, Window-out
Logic input: H or L (signal in each channel)
Pulse input: High or Rising, Low or Falling, Window-in, Window-out


When alarm is detected

  • Display to screen (Digital value of alarm's origin channel is displayed in red)
  • Save alarm information to measurement data file
  • Output alarm signal
    Number of channel: 4 channels (Output channel can be arranged to each source channel in OR condition.)
    Signal type: Open collector (pull-up to 5 V with 10 kΩ resistor), maximum load is the 24 V and 100 mA.
    * Requires Input/Output cable for GL series (B-513 Option).
  • Approximate recording time
    ■ 8 channels of analog input. ■ Data is saved as a GBD file.

    Memory typeData
    capacity
    1MS/s
    (1μs)
    100kS/s
    (10μs)
    1kS/s
    (1ms)
    1S/s
    (1s)
    Built-in RAM4 M samples/ch4 seconds40 seconds66 minutes46 days
    Built-in Flash memory3.9 GBN/AN/A2 days 6 hrs.Over 1 year
    External memory (SD/USB Flash memory)*4 GBN/AN/A2 days 11 hrs.Over 1 year

    ■ 8 channels of analog input with 4 channels of Pulse input. ■ Data is saved as a GBD file.

    Memory typeData
    capacity
    1MS/s
    (1μs)
    100kS/s
    (10μs)
    1kS/s
    (1ms)
    1S/s
    (1s)
    Built-in RAM4 M samples/ch4 seconds40 seconds66 minutes46 days
    Built-in Flash memory3.9 GBN/AN/A1 days 4 hrs.Over 1 year
    External memory (SD/USB Flash memory)*4 GBN/AN/A1 days 7 hrs.Over 1 year

    * When using 8 GB or larger memory, the size of data file will be up to 4 GB. The Relay mode enables extended recording time.


    download datasheet

Write a review

Note: HTML is not translated!
    Bad           Good

Graphtec midi DATALOGGER GL980 Series

  • Product Code: GL980 Series
Minta Penawaran